Quality Coach . Net Book Store Welcome to QualityCoach.Net  Specializing in
 Quality &  Productivity
Home Coffee Shop Safe Shopping Privacy Policy Customer Service Contact Us Shopping Cart 



QualityCoach.Net, Internet Shopping, Wooster, OH

ISO 3744 2010 Acoustics, Download

ISO 3744 2010 Acoustics, Download


10 Digit  ISBN   iso37442010rap    
13 Digit ISBN :  iso37442010rap    

ISO 3744:2010 Acoustics -- Determination of sound power levels and sound energy levels of noise sources using sound pressure -- Engineering methods for an essentially free field over a reflecting plane

This International Standard specifies a method for measuring the sound pressure levels on a measurement surface enveloping a noise source, under essentially free-field conditions near one or more reflecting planes, in order to calculate the sound power level produced by the noise source. It gives requirements for the test environment and instrumentation, as well as techniques for obtaining the surface sound pressure level from which the sound power level of the source is calculated, leading to results which have a grade 2 accuracy.

It is important that specific noise test codes for various types of equipment be established and used in accordance with this International Standard. For each type of equipment, such noise test codes will give detailed requirements on mounting, loading and operating conditions for the equipment under test as well as a selection of the measurement surface and the microphone array as specified in this International Standard.

NOTE 1 The noise test code for a particular type of equipment should give detailed information on the particular surface that is selected, as the use of differently shaped measurement surfaces may yield differing estimates of the sound power level of a source.

Types of noise and noise sources

The method specified in this International Standard is suitable for measurements of all types of noise.

NOTE 2 A classification of different types of noise steady, non-steady, quasi-steady, impulsive, etc.) is given in IS0 2204.

This International Standard is applicable to noise sources of any type and size (e.g. device, machine, component, sub-assembly).

NOTE 3 Measurements according to this International Standard may be impracticable for very tall or very long sources such as chimneys, ducts, conveyors and multisource industrial plants.

Test environment

The test environment that is applicable for measurements made in accordance with this International Standard is an essentially free field near one or more reflecting planes (indoors or outdoors).

Measurement uncertainty

Determinations made in accordance with this Inter- national Standard result, with few exceptions, in standard deviations of reproducibility of the A weighted sound power level equal to or less than I,5 dB (see table 1).

A single value of the sound power level of a noise source determined according to the procedures given in this International Standard is likely to differ from the true value by an amount within the range of the measurement uncertainty. The uncertainty in determinations of the sound power level arises from several factors which affect the results, some associated with environmental conditions in the measurement laboratory and others with experimental techniques.

If a particular noise source were to be transported to each of a number of different laboratories, and if, at each laboratory, the sound power level of that source were to be determined in accordance with this International Standard, the results would show a scatter. The standard deviation of the measured levels could be calculated (see examples in IS0 7574-4:1985, annex 6) and would vary with frequency. With few exceptions, these standard deviations would not exceed those listed in table 1. The values given in table 1 are standard deviations of reproducibility, oR, as defined in IS0 7574-l. The values of table 1 take into account the cumulative effects of measurement uncertainty in applying the procedures of this International Standard, but exclude variations in the sound power output caused by changes in operating conditions (e.g. rotational speed, line voltage) or mounting conditions.

The measurement uncertainty depends on the standard deviation of reproducibility tabulated in table 1 and on the degree of confidence that is desired. As examples, for a normal distribution of sound power levels, there is 90 % confidence that the true value of the sound power level of a source lies within the range 1,645 σR of the measured value and a 95 % confidence that it lies within the range 1,96 σR of the measured value. For further examples, reference should be made to the IS0 7574 series and IS0 9296.


4  The standard deviations listed in table 1 are associated with the test conditions and procedures defined in this International Standard and not with the noise source itself. They arise in part from variations between measurement laboratories, changes in atmospheric conditions if outdoors, the geometry of the test room or outdoor environment, the acoustical properties of the reflecting plane, absorption at the test room boundaries if indoors, background noise, and the type and calibration of instrumentation. They are also due to variations in experimental techniques, including the size and shape of the measurement surface, number and location of microphone positions, sound source location, integration times, and determination of environmental corrections, if any. The standard deviations are also affected by errors associated with measurements taken in the near field of the source; such errors depend upon the nature of the sound source, but generally increase for smaller measurement distances and lower frequencies (below 250 Hz).

5  If several laboratories use similar facilities and instrumentation, the results of sound power determinations on a given source in those laboratories may be in better agreement than would be implied by the standard deviations of table I.

6  For a particular family of sound sources, of similar size with similar sound power spectra and similar operating conditions, the standard deviations of reproducibility may be smaller than the values given in table 1. Hence, a noise test code for a particular type of machinery or equipment making reference to this International Standard may state standard deviations smaller than those listed in table 1, if substantiation is available from the results of suitable interlaboratory tests.

7  The standard deviations of reproducibility, as tabulated in tablel, include the uncertainty associated with repeated measurements on the same noise source under the same conditions (for standard deviation of repeatability, see IS0 7574-l). This uncertainty is usually much smaller than the uncertainty associated with interlaboratory variability. However, if it is difficult to maintain stable operating or mounting conditions for a particular source, the standard deviation of repeatability may not be small compared with the values given in table 1. In such cases, the fact that it was difficult to obtain repeatable sound power level data on the source should be recorded and stated in the test report.

8  The procedures of this International Standard and the standard deviations given in table1 are applicable to measurements on an individual machine. Characterization of the sound power levels of batches of machines of the same family or type involves the use of random sampling techniques in which confidence intervals are specified, and the results are expressed in terms of statistical upper limits. In applying these techniques, the total standard deviation must be known or estimated, including the standard deviation of production, as defined in IS0 7574-1, which is a measure of the variation in sound power output between individual machines within the batch. Statistical methods for the characterization of batches of machines are described in IS0 7574-4.

Electronic Delivery: Remote Access Printing

For the electronic format, please note that you are purchasing a PDF file to print out, not to view on your computer.  Once printed out, the downloaded file is no longer accessible.

Remote Access Printing (RAP) allows you to print out your own "hardcopy". An email with download instructions is provided which allows you to print out a licensed copy of the document.

Select DOWNLOAD for shipping option when ordering this item as no shipping charges apply. Download instructions are normally emailed to you within one to two hours, during normal USA business days. To expedite, please call 1-800-648-9510 after completing order.


ISO 3744 2010 Acoustics, Hardcopy

Product Title:   ISO 3744 2010 Acoustics, Download
10 Digit ISBN/Part Number:   iso37442010rap
13 Digit ISBN:   iso37442010rap
Author:   ISO
Publisher:   ISO
Publication Date:   2010
Media:   Standards / Specifications
Usually ships within:   1
Retail Price:   US$259.00
Your Price:   US$259.00
You Save:   US$0.00

ISO 3744 2010 Acoustics, Download


Ask a question about this product

Add this product to your wish list

Keywords:   noise source,stationery noise,determination of sound power levels and sound energy levels of noise sources using sound pressure engineering methods for an essentially free field over a reflecting plane,acoustics standard,iso 3744,iso 3744 2010

Please review these other products:
ISO 3744 2010 Acoustics, Hardcopy
ISO 3744 2010 specifies methods for determining the sound power level or sound energy level of a noise source from sound pressure levels measured on a surface enveloping the noise source (machinery or equipment) in an environment that approximates to an acoustic free field near one or more reflecting planes.
Our Price: US$269.00

click to see more

10196:noise source,stationery noise,determination of sound power levels and sound energy levels of noise sources using sound pressure engineering methods for an essentially free field over a reflecting plane,acoustics standard,iso 3744,iso 3744 2010

Buying in Bulk?
We love to Quote,Volume
Discounts !


Sale Items, Specials, Clearance Items, Bargains
Browse Our Specials & Clearance Items 

Hot Topics

Six Sigma  

Lean Manufacturing

5S / Visual Factory

ISO 9000 : 2008


Problem Solving

Quality Auditing


Quality Control,Inspection Labels

Quality Control, Inspection Labels.

5S into Action DVD

5S Into Action
Sustaining Results and Realizing the Benefits of 5S.

Lean Enterprise Memory Jogger for Service

Lean Enterprise Memory Jogger for Service.

Please see Our Box Games, Demonstration Kits, Simulation for Teaching, Training and Implementing Quality and Productivity Improvement.

Fragile Lables

Inspection and Shipping Lables

Business Fables 

Fables, Novels, Stories, Tales. These are all popular ways to share a vision of a Quality Organization 

We  supply more than what's on our Web Site.
Don't see what you looking for?
Please Ask 


Search     Browse     Shopping Basket   

QualityCoach.Net hopes you are having a successful experience.  
If you have questions, concerns or ideas for improvement, please take a moment to Contact us.

  Shopping Information   Shipping Information  International Sales  
   Order Status   Logon to your account      Links     B2B Corporate Sales  
Coffee Shop   Customer's Comments    Buy Gift Certificate     
About QualityCoach.Net   Contact Info.    Privacy Policy   Security Statement    Home   

  Please Bookmark our site and check back often. 


Bookstore@QualityCoach.Net Specializing in Quality and Productivity Improvement. Your Source for Business books. Most products are discounted. It is our intent to offer prices lower than major on-line retailers whenever possible. Many products ship the same day that your order is placed. 
Compare; Price, Selection, Delivery, and most of all Service.
You will be Delighted.

Back to Top of Page

Coming soon:  Our New Full Service Book Store Exemplar Books